My Cart
Your Shopping Cart is Empty
Designing a 40 Hz Transmission Line Loudspeaker
|
0 comments
posted by Vincent Zhang
Published by IWISTAO
An Engineering Case Study Using the Markaudio CHN-110
Transmission Line (TL) loudspeaker enclosures are widely regarded for their ability to extend low-frequency response while preserving transient accuracy and smooth impedance behavior.
This article presents an engineering-grade transmission line enclosure design optimized for the Markaudio CHN-110 full-range driver, targeting an acoustic F3 of 40 Hz.
1. Design Objectives
- Achieve a true low-frequency extension of F3 ≈ 40 Hz
- Avoid Helmholtz resonance artifacts typical of bass-reflex enclosures
- Maintain smooth impedance behavior for Class-A and tube amplifiers
- Control cone excursion at low frequencies
- Prioritize transient accuracy and tonal linearity
2. Driver Selection
The selected driver for this study is the Markaudio CHN-110, a 110 mm full-range unit known for its wide bandwidth and moderate total Q.
Key Thiele–Small parameters (manufacturer data):
- Fs ≈ 44.2 Hz
- Sd ≈ 109 cm²
- Qts ≈ 0.42
- Vas ≈ 24.7 L
The moderate Qts makes the CHN-110 particularly suitable for quarter-wave acoustic loading rather than aggressive bass-reflex tuning.
3. Quarter-Wave Transmission Line Theory
Unlike bass-reflex enclosures, which rely on Helmholtz resonance, a transmission line enclosure operates primarily on quarter-wave acoustic resonance. The fundamental design relationship is:
L = c / (4 × f)
where L is the effective acoustic line length, c is the speed of sound (approximately 343 m/s), and f is the target frequency.
For a target F3 = 40 Hz:
L ≈ 2.14 m
After accounting for acoustic damping, which increases the effective acoustic length, the physical folded line length is approximately 1.9 m.
4. Line Geometry and Enclosure Volume
Cross-Sectional Area
Engineering practice derived from quarter-wave modeling recommends that the starting cross-sectional area of the transmission line be proportional to the driver’s effective cone area:
S0 ≈ (1.0–1.2) × Sd
For this design:
- Start of line: ~120 cm²
- End of line (tapered): ~65 cm²
A gentle taper helps suppress higher-order standing waves while preserving low-frequency loading.
Effective Acoustic Volume
Unlike bass-reflex enclosures, a transmission line does not have a single tuning volume. Instead, its effective acoustic volume is defined by:
VTL = ∫0L S(x) dx
where S(x) is the cross-sectional area of the line as a function of distance, and L is the effective acoustic line length. For practical engineering work, this relationship is commonly approximated as:
VTL ≈ Savg × L
- Effective acoustic volume: ~18 L
- Total structural enclosure volume: ~21–22 L
5. Predicted System Performance
Impedance Behavior
The transmission line system exhibits a single, low-Q impedance peak centered near 40 Hz, in contrast to the dual-peak impedance characteristic of bass-reflex enclosures. This results in improved amplifier stability and excellent compatibility with tube amplifiers.
Frequency Response
The predicted frequency response demonstrates smooth low-frequency extension with a −3 dB point at approximately 40 Hz, without the artificial bass emphasis typically associated with port tuning.
Cone Excursion
Because the transmission line continues to provide acoustic loading below resonance, cone excursion remains better controlled than in an equivalent bass-reflex enclosure, particularly in the 40–60 Hz region.
6. Comparison with a Bass-Reflex Enclosure
| Aspect | Bass-Reflex | Transmission Line |
|---|---|---|
| Low-frequency mechanism | Helmholtz resonance | Quarter-wave resonance |
| Impedance behavior | Dual peaks | Single smooth peak |
| Group delay | Higher near tuning | Lower and smoother |
| Port noise | Possible | None |
| Subjective bass | Emphasized | Natural and linear |
7. Practical Construction Notes
- Folded internal path using a three-section “Z” or “S” layout
- Cabinet material: 18 mm MDF or birch plywood
- Heavier damping near the driver, moderate in the middle, minimal near the terminus
8. Conclusion
This engineering study demonstrates that a properly designed damped transmission line enclosure allows the Markaudio CHN-110 to achieve a genuine 40 Hz low-frequency extension without relying on aggressive bass-reflex tuning. Compared to enclosures of similar size, the TL approach offers smoother impedance behavior, improved cone control, and superior transient fidelity, making it an excellent choice for high-quality full-range loudspeaker systems.
References
- Martin J. King, Transmission Line Loudspeaker Design
https://www.quarter-wave.com/ - Martin J. King, Anatomy of a Transmission Line Loudspeaker (PDF)
https://www.quarter-wave.com/TLs/TL_Anatomy.pdf - G. L. Augspurger, “Transmission Lines Updated,” Journal of the Audio Engineering Society, 1980
- Markaudio Loudspeakers Ltd., CHN-110 Datasheet
https://www.markaudio.com/ - Wikipedia, “Transmission Line Loudspeaker”
https://en.wikipedia.org/wiki/Transmission_line_loudspeaker
|
0 comments
Unlocking Sonic Brilliance: Integrating Brass Horn Super Tweeters into Your Hi-Fi System
Previous post
|
0 comments
The Ultimate Guide to Subwoofer Port Tuning for Deep, Powerful Bass
Next post
0 comments