Preamplifier Input and Output Impedance: A Practical Guide to Hi-Fi System Matching
How voltage bridging, output coupling capacitors, and cable capacitance affect the level and frequency response of a Hi-Fi system.
Two Hi-Fi components can each measure flat from 20 Hz to 20 kHz under their specified test conditions. Once connected, a different load or a longer cable can change the frequency response. This is particularly relevant to capacitor-coupled tube stages and unbuffered passive volume controls.
A line-stage preamplifier sits between two electrical interfaces. Its input impedance loads the source, such as a DAC, phono stage, or CD player. Its output impedance affects how the preamp drives the interconnect and power-amplifier input [1].
What Input and Output Impedance Mean in a Preamplifier
Impedance (symbol Z, measured in ohms, Ω) describes how a circuit responds to alternating current. It includes resistance and reactance. Capacitors and inductors can make both the magnitude and phase of the impedance vary with frequency [1].
- Input impedance (Zin) is the load the preamplifier presents to an upstream source. With a higher input impedance, the source supplies less current for a given signal voltage. Line-input impedance varies by model and connection. The Audio Research LS28SE, for example, specifies 50 kΩ single-ended and 100 kΩ balanced [6].
- Output impedance (Zout) is the small-signal source impedance looking back into the preamplifier's output. Lower output impedance reduces the voltage drop under load. The manufacturer's load and signal-level limits still apply [1][4].
Voltage Bridging vs. Impedance Matching: The 10:1 Rule
Modern analog line-level audio generally uses voltage bridging. A relatively high input impedance lets the receiving device take most of the source voltage while drawing little current [1][4]. Legacy 600 Ω audio systems sometimes used equal source and load resistances for maximum power transfer. Electrical digital audio such as coaxial S/PDIF (75 Ω) and balanced AES3 (110 Ω) uses termination matched to the cable's characteristic impedance to control reflections [7].
At audio frequencies a typical home interconnect is short relative to the signal wavelength, so transmission-line effects can usually be neglected. Cable capacitance can still affect the response [4]. The basic voltage-divider equation is:
Vload = Vopen × Zload / (Zout + Zload)
Vopen is the open-circuit source voltage. For frequency-dependent impedances, evaluate the complex quantities at the frequency of interest. For resistive source and load impedances, the following ratios give the loaded voltage relative to the open-circuit voltage:
- 1:1 transfers 50.0% (−6.02 dB). The heavier load draws more current and may increase distortion if the source is driven beyond its capability [3][4].
- 10:1 transfers 90.9% (−0.83 dB). This is a common starting point for checking a line-level connection [1][3].
- 20:1 transfers 95.2% (−0.42 dB).
- 100:1 transfers 99.0% (−0.09 dB).

Solid-State, Tube, and Passive Preamplifier Topologies
Output impedance depends on the circuit, its operating point, and the frequency at which the specification is given.
Active Solid-State Preamplifiers
Op-amp and discrete transistor line stages often use feedback and output buffers to achieve low output impedance. Rod Elliott's solid-state preamplifier, for example, specifies a 100 Ω output and uses a 2.2 µF output coupling capacitor [2]. A resistive 10 kΩ input gives a 100:1 midband ratio in this example.
Vacuum-Tube Preamplifiers
A tube preamplifier's small-signal midband output impedance depends strongly on how the output stage is built:
- Common-cathode (plate-out) stages. In a simple stage with the cathode fully bypassed, the midband output resistance is approximately the tube's plate resistance in parallel with the plate load resistor [8]. For example, 62.5 kΩ for an ECC83S at its stated typical operating point in parallel with 100 kΩ gives about 38 kΩ before the next stage loads it [9].
- Cathode followers. Local voltage feedback lowers the output impedance. For a simple triode follower, 1 / gm is a useful small-signal estimate before accounting for any series output resistor and coupling components. For example, a transconductance of 2.5 mA/V gives about 400 Ω [5].
- Transformer-coupled outputs. The secondary is isolated from the primary's DC. An ideal step-down transformer reduces the source resistance referred to the secondary by the square of the primary-to-secondary turns ratio. In practice, the drive stage, winding losses, inductances, capacitances, and load affect the resulting impedance and bandwidth.
Shigeru Wada Tube Preamp
WHFTPA-SHWA12
6N8P Tube Preamp
WVPA-6N8PPassive Preamplifiers (Attenuators)
A resistive passive preamplifier uses an unbuffered potentiometer or stepped attenuator [3]. With a source whose output resistance is negligible, a potentiometer of total resistance R has its highest unloaded output resistance, R / 4, when its two sections are equal. This is the electrical midpoint, about −6 dB unloaded. The knob position depends on the pot taper. A 50 kΩ pot can therefore reach 12.5 kΩ at that setting. Check the source's drive capability, the power amplifier's input impedance and sensitivity, and the capacitance of the downstream connection.
Output Coupling Capacitors and Low-Frequency Roll-Off in Tube Preamps
Output impedance is often specified at midband. With a series coupling capacitor, the impedance at 20 Hz can be substantially higher. This can occur in capacitor-coupled tube and solid-state designs [2][5].
A series output coupling capacitor (Cout) blocks DC. Its reactance magnitude is XC = 1 / (2πfC). A 1 µF capacitor has about 159 Ω of reactance at 1 kHz and 7.96 kΩ at 20 Hz.

In the one-capacitor model, with cable capacitance negligible at low frequencies, Rout is the approximately resistive output-stage resistance before the capacitor and Rload is the receiving input resistance. The high-pass corner is 3 dB below the loaded midband level:
fHP = 1 / [2π × (Rout + Rload) × Cout]
For a preamplifier with Rout = 500 Ω, the calculated low-frequency response is:
- 1 µF into 47 kΩ. The cutoff is 3.35 Hz, and 20 Hz is 0.12 dB below the loaded midband level.
- 1 µF into 10 kΩ. The cutoff is 15.2 Hz, and 20 Hz is 1.97 dB below midband, with additional phase shift at low frequencies.
- 0.47 µF into 10 kΩ. The cutoff rises to 32.3 Hz, leaving 20 Hz 5.56 dB below midband.
Both 10 kΩ examples have a 20:1 midband load-to-source ratio. Their bass response differs because of the coupling capacitor. Start with the preamplifier manufacturer's minimum load specification, then check the frequency response into your actual load or the preamplifier's output impedance at 20 Hz. For example, Audio Research specifies both a minimum load of 20 kΩ and a maximum load capacitance of 2,000 pF for the LS28SE [6].

Figure 3. Calculated first-order responses for the article's examples, each normalized to its own loaded passband. Each calculation isolates the dominant low- or high-frequency effect. Passband voltage-divider loss is excluded.
Cable Capacitance and High-Frequency Attenuation
At higher frequencies, cable capacitance (Ccable) and the power amplifier's input capacitance (Cin) shunt the signal. In the single-ended model, where the series coupling capacitor has negligible reactance in this part of the band, the capacitances see the preamplifier output resistance and amplifier input resistance in parallel:
fLP = 1 / [2π × (Rout ∥ Rload) × (Ccable + Cin)]
Here, ∥ denotes a parallel combination. The simpler 1 / (2πRoutCcable) estimate applies when the input resistance greatly exceeds the output resistance and input capacitance is negligible. Check the manufacturer's cable data, including whether capacitance is measured conductor-to-conductor or conductor-to-shield. The effective capacitance in a balanced connection depends on the cable construction and how it is driven and received [10].
- Solid-state preamp, 100 Ω into 300 pF. With a high-resistance load and negligible input capacitance, the cable-induced cutoff is about 5.3 MHz.
- Cathode follower, 600 Ω into 300 pF. Under the same assumptions, the cutoff is about 884 kHz.
- Plate-out example, 3 kΩ into 1,500 pF. A 10 m cable at 150 pF/m gives an estimated cutoff of 35.4 kHz and 1.20 dB of loss at 20 kHz under the same assumptions.
- 50 kΩ passive potentiometer at its electrical midpoint. With 12.5 kΩ output resistance and 750 pF from 5 m of 150 pF/m cable, the high-input-resistance estimate is 17.0 kHz. With a 50 kΩ amplifier input and negligible input capacitance, the effective resistance is 10 kΩ, the corner is 21.2 kHz, and 20 kHz is 2.76 dB below the loaded passband.
For a first-order low-pass filter, a 200 kHz corner gives about 0.04 dB attenuation and 5.7° of phase lag at 20 kHz. Treat this as an example of a conservative bandwidth target. Actual cable-length limits depend on total capacitance, source and load impedances, and the preamplifier's specified load limits.
Practical Pairing Guidelines for Hi-Fi Systems
- Check the source-to-preamp interface. Compare the DAC, CD player, or phono stage's output impedance with the preamplifier's line input impedance. Use 10:1 as an initial screen for midband voltage loss, and confirm any minimum load specified for the source.
- Check the preamp-to-power-amp interface. Confirm that the power amp's input impedance meets the preamp's rated minimum load. With capacitor-coupled outputs, check low-frequency response under that load. Compare the preamp's available output voltage with the power amp's input sensitivity to confirm that the system can reach the required level [3][6].
- Read the specifications for the connection you will use. RCA and XLR input impedances can differ or be equal. Yamaha's M-5000 specifies 47 kΩ for both [11]. For a balanced connection, compare differential source and load figures, checking whether a value is quoted per leg.
- Check total capacitance. Multiply the cable's applicable capacitance per meter by its length, include input capacitance where known, and check the resulting high-frequency loss and the manufacturer's maximum capacitive load. High-output-impedance stages and passive attenuators are more sensitive to cable capacitance.
Frequently Asked Questions
What impedance ratio should I look for with a tube preamplifier?
A 10:1 ratio is a starting point for limiting resistive midband voltage loss. For a capacitor-coupled output, check the manufacturer's minimum load and the loaded low-frequency response. Even a 20:1 midband ratio can allow significant loss at 20 Hz.
Why does a tube preamplifier's output impedance rise at low frequencies?
When the output uses a series coupling capacitor, the capacitor's reactance increases as frequency falls. A preamplifier with an output impedance of a few hundred ohms at 1 kHz can therefore present several kilohms at 20 Hz, depending on the capacitor and circuit.
Can I pair a tube preamplifier with a solid-state power amplifier?
Yes. Check the solid-state amplifier's input impedance against the tube preamp's rated minimum load, then check the preamp's response into that load and the power amplifier's input sensitivity. A low-input-impedance power amplifier may require a stage with greater drive capability and, for a capacitor-coupled output, adequate coupling capacitance.
How long can interconnect cables be between a preamplifier and power amplifier?
Cable length depends on the cable's capacitance per meter, the amplifier's input capacitance, and the effective resistance seen by those capacitances. Compare the calculated response and total capacitance with the preamplifier's specifications. Shorter or lower-capacitance cables reduce treble loss when the output impedance is high.
Does a passive preamplifier work with any power amplifier?
Compatibility depends on the source voltage, source impedance, attenuator setting, and the amplifier's input impedance and sensitivity. A resistive attenuator and load produce broadband level loss. Cable capacitance can add treble roll-off, and any upstream coupling capacitor can interact with the load to affect bass response.
Shop Tube Preamplifiers
Shigeru Wada Tube Preamp
WHFTPA-SHWA12
6N8P Tube Preamp
WVPA-6N8PFind More
References
- Robjohns, Hugh. Understanding Impedance. Sound On Sound, January 2003.
- Elliott, Rod. Hi-Fi Tone-Control Preamplifier. Elliott Sound Products, Project 97.
- Norton, Thomas J. Why a Preamp? Stereophile, January 1994.
- Hess, Richard L. Voltage Transmission for Audio Systems. Audio Engineering Society, 1980.
- Blencowe, Merlin. The AC-Coupled Cathode Follower. The Valve Wizard.
- Audio Research. LS28SE Line Stage Preamplifier Specifications.
- Cirrus Logic. CS8416 Digital Audio Receiver Datasheet. AES3 and S/PDIF receiver termination.
- Blencowe, Merlin. Fundamentals of Amplification. Designing Valve Preamps for Guitar and Bass, Chapter 1, section 1.20.
- JJ Electronic. ECC83S / 12AX7 Datasheet.
- Belden. 8451 Cable Technical Data Sheet.
- Yamaha. M-5000 Power Amplifier Specifications.
The KT66 Vacuum Tube in Hi-Fi and Guitar Amplifiers
Previous post
Preamplifier vs. Power Amplifier Audio Specifications: Similarities, Differences, and System Matching
Next post
0 comments